LaserFreak Forum
ALC 68C Remote
ALC 68C Remote
Hallo zusammen....
sitze hier gerade im Labor vor einem kleinen Problem (eigentlich 2):
1) hat jemand die Schaltpläne vom ALC 68C Netzteil ?
2) Wer hat eine genaue Belegung für die Sub-D9 Schnittstelle des PSU vom ALC 68C ? Mir fehlt nämlich die Fernbedienung..... aber an sich sollte die doch nachbaubar sein..!?
Bitte um umgehende Hilfe wenn jemand Infos hat !
sitze hier gerade im Labor vor einem kleinen Problem (eigentlich 2):
1) hat jemand die Schaltpläne vom ALC 68C Netzteil ?
2) Wer hat eine genaue Belegung für die Sub-D9 Schnittstelle des PSU vom ALC 68C ? Mir fehlt nämlich die Fernbedienung..... aber an sich sollte die doch nachbaubar sein..!?
Bitte um umgehende Hilfe wenn jemand Infos hat !
Hi,
ohne Gewähr: Pin1 und Pin5 hängen dierkte (oder über Vorwiderstände?) am Optokoppler. Eine Steuerspannung zwischen 0 und x Volt regelt den Strom. Häng ein Amperemeter rein, mehr als 10mA würde ich dem Optokoppler nicht geben. Polarität weiß ich nicht mehr, kann aber beim Optokoppler nichts zerstören. Am besten ein Labornetzteil ran, auf Null reglen, und die Spannung langsam hochdrehen und den Strom durch den Optokoppler im Auge behalten. Evtl. einen 1K Widerstand in Reihe schalten, um auf Nummer sicher zu gehen.
Wenn sich der Röhrenstrom nicht regeln läßt, Polarität umkehren.
Manche ALC Netzteile (z.B. bei Meditec EIL4000 Variante) haben einen Strommessausgang an der Buchse. Da liegt dann ein Abgriff über dem internen Shunt, der in Reihe mit der Passbank liegt. Vorsicht! Netztpotentilal.
Gruß
John
PS: EIL4000 Plan habe ich elektronisch hier, ALC68 Plan nur als Papiervariante. Bei Interesse: eMail.
ohne Gewähr: Pin1 und Pin5 hängen dierkte (oder über Vorwiderstände?) am Optokoppler. Eine Steuerspannung zwischen 0 und x Volt regelt den Strom. Häng ein Amperemeter rein, mehr als 10mA würde ich dem Optokoppler nicht geben. Polarität weiß ich nicht mehr, kann aber beim Optokoppler nichts zerstören. Am besten ein Labornetzteil ran, auf Null reglen, und die Spannung langsam hochdrehen und den Strom durch den Optokoppler im Auge behalten. Evtl. einen 1K Widerstand in Reihe schalten, um auf Nummer sicher zu gehen.
Wenn sich der Röhrenstrom nicht regeln läßt, Polarität umkehren.
Manche ALC Netzteile (z.B. bei Meditec EIL4000 Variante) haben einen Strommessausgang an der Buchse. Da liegt dann ein Abgriff über dem internen Shunt, der in Reihe mit der Passbank liegt. Vorsicht! Netztpotentilal.
Gruß
John
PS: EIL4000 Plan habe ich elektronisch hier, ALC68 Plan nur als Papiervariante. Bei Interesse: eMail.
-
- Beiträge: 173
- Registriert: Sa 04 Jan, 2003 2:37 pm
- Wohnort: Munich
Hi,
also der Pin 1 gehört an + und der 5er an 0V. Geregelt wird mit einer Spannung von 0-5V, wenn die Polarität nicht stimmt passiert gar nichts, wenn die Spannung über 5V geht dann rauchts Noch was: Die Regelung erfolgt nicht linear, bei meinem NT geht´s erst bei 1,2V los und bei 3,5V habe ich dann schon fast Volldampf. Ist glaube ich abhängig vom min. und max. Röhrenstrom der eingestellt ist.
Hoffe geholfen zu haben.
Grüße,
Alex
also der Pin 1 gehört an + und der 5er an 0V. Geregelt wird mit einer Spannung von 0-5V, wenn die Polarität nicht stimmt passiert gar nichts, wenn die Spannung über 5V geht dann rauchts Noch was: Die Regelung erfolgt nicht linear, bei meinem NT geht´s erst bei 1,2V los und bei 3,5V habe ich dann schon fast Volldampf. Ist glaube ich abhängig vom min. und max. Röhrenstrom der eingestellt ist.
Hoffe geholfen zu haben.
Grüße,
Alex
- rheinperchten
- Beiträge: 394
- Registriert: Di 08 Mär, 2005 2:38 pm
- Wohnort: Leverkusen
- Kontaktdaten:
Also um das Uraltthema nochmal aufzugreifen.......
Habe ein EIL 4000 und möchte per Fernsteuerung den Strom regeln.
Wer hat sende bitte mal ne genaue Belegung und nen Tip wie man das macht...biiiiiittteeee
rheinperchten@gmx.de
Habe ein EIL 4000 und möchte per Fernsteuerung den Strom regeln.
Wer hat sende bitte mal ne genaue Belegung und nen Tip wie man das macht...biiiiiittteeee
rheinperchten@gmx.de
- pitchoun
- Beiträge: 500
- Registriert: Di 24 Mai, 2005 12:24 am
- Do you already have Laser-Equipment?: divers
- Wohnort: Haute-Loire
Hello,
I have an Meditec EIL 4000 PSU and i must build my own remote.
But i haven't really understand the topic because i don't speak german and google translation is very bad.
So any can give to me the schematics of the remote ? or translate me the most important point of topic in english or french ?
And if someone can give me the schematics of the full power supply, it will be very helpfull for me.
you can contact me by private message or my email is pitchoun43@msn.com
thanks a lot
I have an Meditec EIL 4000 PSU and i must build my own remote.
But i haven't really understand the topic because i don't speak german and google translation is very bad.
So any can give to me the schematics of the remote ? or translate me the most important point of topic in english or french ?
And if someone can give me the schematics of the full power supply, it will be very helpfull for me.
you can contact me by private message or my email is pitchoun43@msn.com
thanks a lot
Euh j'ai dit une bétise ?!
- pitchoun
- Beiträge: 500
- Registriert: Di 24 Mai, 2005 12:24 am
- Do you already have Laser-Equipment?: divers
- Wohnort: Haute-Loire
Hello,
I have an Meditec EIL 4000 PSU and i must build my own remote.
But i haven't really understand the topic because i don't speak german and google translation is very bad.
So any can give to me the schematics of the remote ? or translate me the most important point of topic in english or french ?
And if someone can give me the schematics of the full power supply, it will be very helpfull for me.
you can contact me by private message or my email is pitchoun43@msn.com
thanks a lot
I have an Meditec EIL 4000 PSU and i must build my own remote.
But i haven't really understand the topic because i don't speak german and google translation is very bad.
So any can give to me the schematics of the remote ? or translate me the most important point of topic in english or french ?
And if someone can give me the schematics of the full power supply, it will be very helpfull for me.
you can contact me by private message or my email is pitchoun43@msn.com
thanks a lot
Euh j'ai dit une bétise ?!
- rheinperchten
- Beiträge: 394
- Registriert: Di 08 Mär, 2005 2:38 pm
- Wohnort: Leverkusen
- Kontaktdaten:
- pitchoun
- Beiträge: 500
- Registriert: Di 24 Mai, 2005 12:24 am
- Do you already have Laser-Equipment?: divers
- Wohnort: Haute-Loire
I have done this small schématics, is it good ?
Where i must add a 1K resistor ?
The PSU have 2 potentiometer for MIN and MAX current adjust. Actually my PSU can give 35A but my tube (Omnichrome 543) can only get 15A max. So how can i do the adjustment without over current the tube ?
i should decrease the value to MIN and slowly increase them to get the max current tube ?
Thanks a lot to fast response and sorry to have posted 2 time the same reply.
Where i must add a 1K resistor ?
The PSU have 2 potentiometer for MIN and MAX current adjust. Actually my PSU can give 35A but my tube (Omnichrome 543) can only get 15A max. So how can i do the adjustment without over current the tube ?
i should decrease the value to MIN and slowly increase them to get the max current tube ?
Thanks a lot to fast response and sorry to have posted 2 time the same reply.
Euh j'ai dit une bétise ?!
- Dr. Burne
- Beiträge: 2385
- Registriert: Di 07 Aug, 2001 12:00 pm
- Do you already have Laser-Equipment?: Pangolin Pro und Intro inkl. Beyond
Jede Menge alte Lasertechnik die groß und schwer ist
Baue grad pure Diode Main Projektor aus und 2 LW DS900
Molectron Powermeter mit PM1 und 10 Sonde - Wohnort: Halle(Saale)
- Kontaktdaten:
- rheinperchten
- Beiträge: 394
- Registriert: Di 08 Mär, 2005 2:38 pm
- Wohnort: Leverkusen
- Kontaktdaten:
Wer ist online?
Mitglieder in diesem Forum: 0 Mitglieder und 15 Gäste