please help with scanners

Scanning, Scanners, scannermirrors, scanneraxes, torsionrods and driver interface cards.
Antworten
tonix
Beiträge: 26
Registriert: Mo 05 Okt, 2009 9:59 pm
Do you already have Laser-Equipment?: Equipment

please help with scanners

Beitrag von tonix » Di 20 Okt, 2009 8:08 am

Please help me with this scanners. In the picture the scanners of Cambridge Technology 52K with aperture 5x8 mm.

Tell me please it's normal effect in the picture? or i have a bad scanners?

Thanks
Du hast keine ausreichende Berechtigung, um die Dateianhänge dieses Beitrags anzusehen.

Benutzeravatar
guido
Beiträge: 6341
Registriert: Do 20 Dez, 2001 12:00 pm
Do you already have Laser-Equipment?: Easylase, Netlase, Laser von 1..15W.
Entwickler von Dynamics + Mamba X4 .
Lasershow Hard / Software .
Wohnort: 32469 Petershagen
Kontaktdaten:

Re: please help with scanners

Beitrag von guido » Di 20 Okt, 2009 10:22 am

Hi,

which Scanners with which Drivers are we talking about ?
First, its good to see that your Drivers need to be Readjusted.
One of them is faster than the other.

Are Original Mirrors mounted ? Looks like the Mirrors swing.
Do you see this at all Scanspeeds or only at 12K, 22K for Example ?

Which Scanspeed did you use as you take the Photo ?

goamarty
Beiträge: 1488
Registriert: Fr 05 Sep, 2008 10:15 am
Do you already have Laser-Equipment?: 190mW RGY + einige Module
Wohnort: Wien

Re: please help with scanners

Beitrag von goamarty » Di 20 Okt, 2009 2:24 pm

Perhaps there is some noise or high frequency hum on the Y-signal. This could originate from bad SMPS.

tonix
Beiträge: 26
Registriert: Mo 05 Okt, 2009 9:59 pm
Do you already have Laser-Equipment?: Equipment

Re: please help with scanners

Beitrag von tonix » Di 20 Okt, 2009 5:00 pm

goamarty hat geschrieben:Perhaps there is some noise or high frequency hum on the Y-signal. This could originate from bad SMPS.
What is SMPS ?

tonix
Beiträge: 26
Registriert: Mo 05 Okt, 2009 9:59 pm
Do you already have Laser-Equipment?: Equipment

Re: please help with scanners

Beitrag von tonix » Di 20 Okt, 2009 5:04 pm

guido hat geschrieben:Hi,

which Scanners with which Drivers are we talking about ?
First, its good to see that your Drivers need to be Readjusted.
One of them is faster than the other.

Are Original Mirrors mounted ? Looks like the Mirrors swing.
Do you see this at all Scanspeeds or only at 12K, 22K for Example ?

Which Scanspeed did you use as you take the Photo ?
used CH6815 drivers of cambridge technology.
i see this effect by all speed.
this foto make at 28K speed.

mirror not original - mounted 5x8 mm aperture

Benutzeravatar
guido
Beiträge: 6341
Registriert: Do 20 Dez, 2001 12:00 pm
Do you already have Laser-Equipment?: Easylase, Netlase, Laser von 1..15W.
Entwickler von Dynamics + Mamba X4 .
Lasershow Hard / Software .
Wohnort: 32469 Petershagen
Kontaktdaten:

Re: please help with scanners

Beitrag von guido » Di 20 Okt, 2009 5:39 pm

Hi,

SMPS = Swítching Mode Power Supply
Can the used Powersupplies deliver enought Power ?? Calculate >= 2.5A Minimum.
( I dont know the Driver you are using... )
Thickness of the Mirrors ? If the are too thin this could also be the Reason, normally only to see at some Speeds..

Please adjust Servogain / LF and HF Damping that the Circle is round and in the Middle of the inner Square.
Maybe the Driver is "overdriven" and so he beginns to swing .
@ 35-40Kpps. Which D/A Card are you using ?

tonix
Beiträge: 26
Registriert: Mo 05 Okt, 2009 9:59 pm
Do you already have Laser-Equipment?: Equipment

Re: please help with scanners

Beitrag von tonix » Mi 21 Okt, 2009 11:02 am

It is my scanner and driver foto.
Du hast keine ausreichende Berechtigung, um die Dateianhänge dieses Beitrags anzusehen.

tonix
Beiträge: 26
Registriert: Mo 05 Okt, 2009 9:59 pm
Do you already have Laser-Equipment?: Equipment

Re: please help with scanners

Beitrag von tonix » Mi 21 Okt, 2009 11:07 am

guido hat geschrieben:Hi,

SMPS = Swítching Mode Power Supply
Can the used Powersupplies deliver enought Power ?? Calculate >= 2.5A Minimum.
( I dont know the Driver you are using... )
Thickness of the Mirrors ? If the are too thin this could also be the Reason, normally only to see at some Speeds..

Please adjust Servogain / LF and HF Damping that the Circle is round and in the Middle of the inner Square.
Maybe the Driver is "overdriven" and so he beginns to swing .
@ 35-40Kpps. Which D/A Card are you using ?
Thanks for you answer. But please - can you tell me how i can adjust Servogain / LF and HF Damping?

And if you know - For what everyone potentiometer is answers?

Benutzeravatar
guido
Beiträge: 6341
Registriert: Do 20 Dez, 2001 12:00 pm
Do you already have Laser-Equipment?: Easylase, Netlase, Laser von 1..15W.
Entwickler von Dynamics + Mamba X4 .
Lasershow Hard / Software .
Wohnort: 32469 Petershagen
Kontaktdaten:

Re: please help with scanners

Beitrag von guido » Mi 21 Okt, 2009 11:21 am

Hi,

if you got the Drivers without any Manual you also got a little Problem :-)

Contact Cambridge and ask for the Manual as PDF.

If you never adjust a Scannerdriver before: HANDS OFF !!

As I adjust my first Scannerdriver without Help 4-6 Hours were gone..

Its also possible to destroy the Galvos with wrong adjustment.

tonix
Beiträge: 26
Registriert: Mo 05 Okt, 2009 9:59 pm
Do you already have Laser-Equipment?: Equipment

Re: please help with scanners

Beitrag von tonix » Mi 21 Okt, 2009 11:33 am

guido hat geschrieben:Hi,

if you got the Drivers without any Manual you also got a little Problem :-)

Contact Cambridge and ask for the Manual as PDF.

If you never adjust a Scannerdriver before: HANDS OFF !!

As I adjust my first Scannerdriver without Help 4-6 Hours were gone..

Its also possible to destroy the Galvos with wrong adjustment.
Thank you very match!

What you can said about this scanner and driver ?

Benutzeravatar
guido
Beiträge: 6341
Registriert: Do 20 Dez, 2001 12:00 pm
Do you already have Laser-Equipment?: Easylase, Netlase, Laser von 1..15W.
Entwickler von Dynamics + Mamba X4 .
Lasershow Hard / Software .
Wohnort: 32469 Petershagen
Kontaktdaten:

Re: please help with scanners

Beitrag von guido » Mi 21 Okt, 2009 12:45 pm

On the first Look:

Scanner designed for larger Apertures and not usuable for Laserhows.
Normally theese Galvos are not so fast but very precise.

The Question about the Scanspeed you drive at the ILDA Testpictures is
never been answered..if it was 52K go down to 40K and re-adjust them..

tonix
Beiträge: 26
Registriert: Mo 05 Okt, 2009 9:59 pm
Do you already have Laser-Equipment?: Equipment

Re: please help with scanners

Beitrag von tonix » Mi 21 Okt, 2009 1:21 pm

guido hat geschrieben:On the first Look:

Scanner designed for larger Apertures and not usuable for Laserhows.
Normally theese Galvos are not so fast but very precise.

The Question about the Scanspeed you drive at the ILDA Testpictures is
never been answered..if it was 52K go down to 40K and re-adjust them..

Thank you very match

Antworten

Zurück zu „Scanner & Scanner Driver“

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 2 Gäste